Research on the Key Points of Structural Design of General Purpose Mold for Layered Reiteration Plat
1. College of Civil Engineering, Henan University of Technology, Zhengzhou 450001, China
2. China Construction Science and Technology Henan Co., Ltd., Zhengzhou 450004, China
3. The Fourth Construction Co., Ltd. of CSCES 7th Division, Xi’an 710100, China
| Abstract: | Based on the case of a prefabricated component factory, this paper adopts the universal design of a layered reiteration plat mold as the research object to improve the universality of layered reiteration plat molds and reduce the cost of reiteration plat molds without affecting the quality of the components or production efficiency. The traditional layered mold is not limited by the spacing of the ribs and can prevent the ribs from floating and leaking. It has been widely used in the production of reiteration plates, but the generality of the mold is still limited because the traditional layered mold is designed according to the size of the fixed components, and a set of molds cannot be used for the production of other reiteration plates without cutting or transformation. In this paper, a universal purpose mold for layered reiteration plates is studied. This mold can be combined into any plane shape and size by moving any one of the three sides of the mold and combining the two moduli, which completely realizes the universality of the mold. At the same time, in this paper, the design of the universal mold structure was optimized, eliminating the problem of nut pollution and the problem of edge angle loss during demolding. This optimization significantly enhanced the production efficiency and quality of reiteration plates and holds high potential for widespread adoption. |
| Keywords: | Reiteration Plate; Layered Mold; Universal Design of Mold; Key Points of Design |
| DOI: | 10.57237/j.cear.2024.02.001 |
View:
Downloads:
收稿日期: 2024-02-29
接受日期: 2024-04-13
在线出版日期: 2024-04-19
参考文献
| [1] | Zhou Qiang, Ma Jinhua, Zhang Degang et al. Research on Standardization and Generalization of PC Component Mold [J]. Concrete and Cement Products, 2020, 03: 82-85. |
| [2] | Luo Han, Zhou Haitao, Gao Zhongxue. Research status and analysis of Reinforced concrete composite plate mold [J]. Sichuan Building Materials, 2021, 47(01): 234-236. |
| [3] | Li Heguang, Wang Wanjiang. Analysis on PC-component modular Universal mold for prefabricated buildings [J]. Building Technology, 2022, 53(02): 244-246. |
| [4] | Zhao Yongqiang, Hu Zhongping, Zheng Zhiyuan. Research on standardization of prefabricated components in prefabricated buildings [J]. Building Structure, 2022, 52: 1693-1698. |
| [5] | Wang Jin, Cao Qing, Li Yan. Discussion on some Problems in the design of composite floor slab of prefabricated building [J]. Building Structure, 2017, 47: 890-892. |
| [6] | Tian He. Analysis of common problems and improvement schemes of prefabricated steel truss composite floor [J]. Architectural Structure, 2022, 52: 1732-1737. |
| [7] | LI Xinmei. Research on the application of product standardization design in high-rise residential projects [J]. Engineering Construction Standardization, 2023(12): 107-111. |
| [8] | Yu Hongping, Zhao Hui, Ma Siyao et al. Study on comparison and standardized design of double-sided superimposed shear wall system [J]. Urban Building Space, 2023, 30(01): 122-124. |
| [9] | Ma Zhonghua, Fu Xiubing, Song Gang et al. Research on the design of thick plate transfer structure for a subway roof building [J]. Shanxi Architecture, 2024, 50(03): 60-63. |
| [10] | Hu Dao-hang, Zhao Xin. Design of continuous renovation of super tall building structure with integrated viscous damping boom damping Device [J]. Journal of Building Structures, 2024, 45(04): 1-11. |
| [11] | Cao Zijian. Discussion on the application of standardized residential design (intelligent part) [J]. Intelligent Building, 2021(02): 14-16. |
| [12] | Ou Yihong, Sun Yining, Liu Degui et al. Research and application of inclined cylindrical support form technology for high inclination concrete [J]. Building Structures, 2023, 53(S2): 1977-1981. |
| [13] | Li Xubin, Zhang Minghao, Lian Bizheng et al. Research on Construction Technology of Aluminum Alloy formwork applied in prefabricated Engineering [J]. Building Technology Development, 2023, 50(12): 56-58. |
| [14] | HU Zhe, Du Xiaolei, Wang Yang et al. Research on Steel Formwork Design and Application of Steel-Mixed Composite beam [J]. Engineering Research, 2023, 8(22): 116-118. |
| [15] | Feng Xin, Chen Ming, Tian Zhichang. Classification and research review of concrete composite slabs [J]. Building Structures, 2024, 54(01): 138-144. |
| [16] | Yu Jinghai, He Mengjie, Zhang Shuhui et al. Experimental study on mechanical performance of composite slabs of prestressed concrete steel tube truss under two-stage loading [J]. Building Structures, 21, 51(05): 80-85. |
| [17] | WU Fangbo, Liu Biao, Deng Libin et al. Experimental study on static Performance of prestressed concrete Composite hollow floor [J]. Journal of Building Structures, 2014, 35(12): 10-19. |
